Results 1 to 12 of 12

Thread: Toyota FAQ versjon 2.0

  1. #1
    Fotograf knixen's Avatar
    Join Date
    Jan 2007
    Location
    Tromsø
    Posts
    4,195

    Default Toyota FAQ versjon 2.0

    *******Offisiell Toyota Bibel/FAQ 2.0*****(red 4/2009)
    Denne er komplementert, det mangler nok emner. Men det kommer mer underveis og hvis noen kommer over noe som mangler så send meg en pm. Fint om alle hjelper til slik at denne dekker det meste av teknisk info om våre biler.

    Mange takk,
    Knut (Knixen)

    Offisiell PBB Toyota Bibel/FAQ


    - - - - - - - - - - - Disclaimer - - - - - - - - - - -

    Pirate4x4.com Bulletin Board is known for its wealth of information and this Toyota Truck and 4Runner FAQ is designed to list the most common questions and answers that frequently get asked. The information in this post is a collection of everyone’s efforts to provide very accurate and detailed information but the website cannot be held responsible for mistakes. If you find false information and have good proof stating so, please contact the person that posted it so it can get corrected and will not mislead other people. Remember keeping the accuracy of this FAQ is a group effort.

    - - - - - - - - - - - Disclaimer - - - - - - - - - - -


    Previous Frequently Asked Question Databases Thanks guys!
    Feb 2002 http://www.pirate4x4.com/forum/showt...hreadid=110627 by Entropy
    Old school http://www.barneymc.com/toy_root/toytop.htm by Barney

    How to Google to Search .....

    The search button is sometimes temporarily disabled for everyone but red star ( ) members due to unusually high server loads. So if you DON'T have a red star - buck up the $20/yr or use just use Google Advanced Search. Just put "www.pirate4x4.com" into the domain search field plus what your looking for. So if you want to find info on 7mge motor swaps, just type this into the google search field - "site: pirate4x4.com 7mge motor swap".

    How to use the search feature for three letter words!

    I understand that search leaves out three letter words, so here is a little information for the future. If you want to search for IFS (or any other three letter or number combination), use an asterisk (*) like this: IFS* or *IFS. The search will use that as a wildcard and voíla!

    Oh please remember that this is Pirate4x4.
    is a freindly smiley.
    is NOT a freindly smiley.

    And fully expect to get flamed if you ask a question that can be answered in this FAQ! We don't like answering the same question every week, week after week, hence why this FAQ was written, so you better read up if you plan to post questions here.

    And for those that like to ask the same old questions, so you don't have to search for them, try these sites.

    http://www.4x4wire.com/toyota/
    http://www.yotatech.com/forumindex.php?
    http://forums.off-road.com/toyota-suvs-trucks/
    http://www.pirate4x4.com/forum/showthread.php?t=459180

    They are much "nicer" and more tolerant of the same questions being asked every week over there! But if you want hardcore tech - keep reading!

    IN ADDITION TUESDAY IS THE ONLY DAY YOU MIGHT GET AN ANSWER TO A NOOB QUESTION. OTHER WISE SEARCH!!!!!!!!!!!!!! OR ASK IT IN THE APPROPRIATE FORUM---> http://www.pirate4x4.com/forum/forumdisplay.php?f=43

    .
    .
    .
    .
    .
    .
    .

    THIS ENTIRE BIBLE IS IN ALPHABETICAL ORDER!!!!!

    2wd to 4wd conversion faq the information thread
    http://www.pirate4x4.com/forum/showthread.php?t=496869



    AFM Info - Idle mixture screw drilled out? How to set if back to OEM spec
    http://www.pirate4x4.com/forum/showt...926&highlight=




    Ammo Can Dimensions
    http://www.pirate4x4.com/forum/showt...mmo+dimensions



    Axle info - Toyota

    Toyota Mini Truck Front Axle Identification
    79-80 no gusset
    81-83 short gusset (to u-bolts)
    84-85 long gusset (past u-bolts)

    Stock Toyota front axle measurements for comparison:
    55.5" wide, 29" spring perch centers, '79-85 Toyota trucks and 4runners, SA Hubs
    58.25" wide, 29" spring perch centers, '79-85 Toyota trucks and 4runners, IFS Hubs
    63.5" wide, (set up for coil springs) 90-97 FJ80 and FZJ80 Landcruisers
    '86-95 IFS front end is about 58.5" wide
    '93-98 T100 IFS front end is about 65" wide

    Toyota Rear Axle Widths:
    55" wide, '79-85 4wd trucks/4runners - 6 Lug
    58" wide, '86-95 4wd trucks/4runners - 6 Lug
    56" wide, '79-95 2wd Trucks - 5 Lug
    60.75" wide, '95.5-up Tacomas/4runners
    66.75" wide, '93-98 T100 trucks



    Axle / Differential Breathers
    The actual thread size for Toyota breathers is 1/8" British 28 Thread Per Inch.
    1/8" NPT thread is close, but it is 27 Thread per inch.


    Axle Rebuild Picture Thread, Toyota 8" Front Solid Axle
    http://www.birfield.com/~morgan/tech/axle/


    Axle- Stock pre 1985 Picture Thread-
    http://pirate4x4.com/forum/showthread.php?p=9520893


    Bellhousings - HUGE resource for engine swap bellhousings!!
    http://www.jeeps-offroad.com/f41/eng...housings-4740/


    Bellhousing bolt patterns by MarlinCrawler
    84' to 03' Toy 5 speed trannies use two bellhousing to transmission bolt patterns.
    small 9 bolt pattern
    84-88' G52,54 carb 22R
    89-95' G58 EFI 22R
    85-88' W56 early EFI 22R
    89-95' W56 late EFI 22R
    96-03' W59 EFI 2.7

    large 9 bolt pattern
    86-87' R151F EFI Turbo 22R
    88-95' R150F EFI 3.0V6
    96-03' R150F EFI 3.4V6




    Bikini Tops - 4Runners
    http://www.pirate4x4.com/forum/showthread.php?t=254738
    http://www.4crawler.com/4x4/CheapTri...op/index.shtml
    http://www.pirate4x4.com/forum/showthread.php?t=167640




    Birfield Stuff

    Separating a birf from and axle:
    http://www.pirate4x4.com/forum/showt...839#post334839

    What everyone needs to know about Longfields by desertoy
    http://www.pirate4x4.com/forum/showt...ght=Longfields
    The above list should probably be also applied to any type of aftermarket Birfield / Marfield / Newfield/ Longfield/ Smurfield / WhateverField....

    How to change one quickly Camo method
    Pull locking hub cap and remove snap ring.
    Unbolt seal/felts on back of knuckle.
    Unbolt brake caliper and tie out of the way. (can be skipped if you have long brake lines)
    Unbolt steering arm. (leave bottom knuckle cap alone)
    Pull entire outer knuckle assembly off of axle.
    Swap in your parts.
    Put it back together.
    It's a big-time shortcut since you don't need to mess with the 54mm socket or wheel bearings.

    Heres a post showing the slow method - but it "lets" you repack everything...
    Longfield 30 spline & hub gear install
    http://www.pirate4x4.com/forum/showt...=482812&page=2




    Bob length pictures for a 4Runner
    http://www.pirate4x4.com/forum/showthread.php?t=394500



    Bobbing a 4Runner - First Gen
    See http://www.pirate4x4.com/forum/showt...hreadid=132555 for a text version of an article I wrote on bobbing the back of a 4runner including the fiberglass top.
    Update: Article pictures are now here: http://www.pirate4x4.com/forum/showthread.php?t=394399


    Bobbing a 4Runner (Super-Bob)- First Gen
    http://www.pirate4x4.com/forum/showthread.php?t=62246
    http://www.pirate4x4.com/forum/showthread.php?t=488188


    Bobbing a 4Runner - Second Gen
    See: http://www.pirate4x4.com/forum/showt...bobbed+4runner



    Bobbing a Bed for an extra cab on a std cab frame
    http://www.pirate4x4.com/forum/showt...hreadid=109638



    Brakes - Bleeding
    This is the proper way to bleed your brakes to avoid spongy brakes, etc...
    Originally posted by Opp's
    ----------------------------------------------------
    "...This is from the FSM and it works great..."
    1. Drivers side rear
    2. Passenger side rear
    3. Passenger side front
    4. Drivers side front
    5. LSPV (Load sensing proportioning valve)
    ----------------------------------------------------

    Brakes-ErikB 1 Ton Master Cylinder upgrade-
    http://home.4x4wire.com/erik/4runner/brakes/

    Brakes- Load Sensing Proportioning Valve Tech and Replacement
    http://www.pirate4x4.com/forum/showthread.php?t=489391

    Brake Boosters - Single Vs Dual
    http://www.pirate4x4.com/forum/showthread.php?t=132252



    Brake Boosters - Dual diaphram on First Gen (79-83)
    http://www.pirate4x4.com/forum/showthread.php?t=564587



    Brakes - Drum rebuild
    http://www.pirate4x4.com/forum/showthread.php?t=509586



    Brake Lines
    Toyota Fittings are 10mm x 1.00 thread with an inverted flare.
    ProComp #7210 are Longer than stock Stainless Steel brake lines. (set of three)
    One piece 23" long replacement brake line for the front is Napa #38688
    [EDIT: This turns out to be a front line from a 90-96 Nissan 300ZX if you wanna get one from somewhere else.]

    The flexible rear brake line (goes from the hardline to the rear axle) is commonly used for extending the front and rear brakes lines since it has one male end and one female end. So when these lines are swapped inline with the stock lines, and you will have plenty of room for extra lift and flexy suspensions. The Napa #38256 is the stock length (19" long) rear flexible brake hose. Napa #36881 is 11" long if you need one a bit shorter.

    Good source for custom SS Brakelines (recommended by steveh)
    http://www.pirate4x4.com/forum/showthread.php?t=449419



    Brake Master Cylinder info
    In addition to the Rotor swap, some people like to put bigger MCs in so that they have more fluid movement.
    In this case, you want to acquire a Master Cylinder for a V6 truck or 4runner. It should be the 1" Bore. This is pretty much a bolt in replacement. Requiring you to move some brake lines slightly at worst.
    http://www.pirate4x4.com/forum/showthread.php?t=251887



    Brakes - Rear Disc / Disk Brakes FAQ
    http://www.pirate4x4.com/forum/showthread.php?t=281059
    Detailed Disk Brake Write Up-
    http://www.pirate4x4.com/forum/showthread.php?t=452546


    Brake Rotor Swap – Vented Front

    Some folks like to swap out their solid rotors for vented rotors. This is a simple and somewhat inexpensive modification. I did this swap because my brakes were getting very hot and making some very annoying noises. If you can change your brakes you should not have any problem with this swap.

    79-80 toyota mini axles -> Rotor bolts onto hub with 6 bolts and the wheel studs are pressed into the hub only. For Land Cruiser vented brake swap you must use 79-80 LC rotors.
    81-85 toyota mini axles -> Rotor bolts onto the hub with 2 bolts and the wheel studs are prasses through the hub and is pressed into the rotor. For the Land Cruiser vented rotor swap you must use 81+ LC rotors. Uses Toyota 90942-02053, Dorman #610-264 or Napa 641-3126 wheel studs.

    The Landcruiser rotors are wider because they are vented but otherwise fit right on with no other modification besides the need to run a IFS caliper.
    The caliper comes in two flavors... one has two larger pistons and two smaller, and another has four pistons that are the same size. The ones with four large pistons would technically give you more braking force. I used the same pads because mine were still fairly new... so you don't need new pads unless yours are low.

    Build-Ups, Toyota Project Rigs - Ultimate Collection
    http://www.pirate4x4.com/forum/showthread.php?t=399607



    Built Rigs - Whats Your Trucks Specs / Typical / Standard Issue
    http://www.pirate4x4.com/forum/showthread.php?t=307983


    Bumpers
    Front winch bumper pictures:
    1st gen- http://www.pirate4x4.com/forum/showt...=front+bumpers
    Rock Defense- http://www.pirate4x4.com/forum/showt...=front+bumpers
    Tube Bumpers- http://www.pirate4x4.com/forum/showt...=front+bumpers
    Rear 4Runner Bumpers pictures:
    http://www.pirate4x4.com/forum/showthread.php?t=482618
    Square Tube Front Bumpers
    http://www.pirate4x4.com/forum/showthread.php?t=761629


    Bump Stop Tech.
    http://www.pirate4x4.com/forum/showt...19#post2920419


    Carb Tuning
    how to get it with a toyota carb............
    http://www.pirate4x4.com/forum/showt...hreadid=165996
    Stock Carb Pictures-
    http://www.pirate4x4.com/forum/showthread.php?t=437673
    22R Carburetor FAQ-
    http://www.bluebassdesign.com/boonin/carb_faq/


    Caster Angle - Solid Axle
    Stock = is 1°30' ± 45' positive.
    Recommended for lifted vehicles with larger tires = 5-7° positive
    http://www.pirate4x4.com/forum/showt...54#post5942854
    Discussion about caster settings-
    http://www.pirate4x4.com/forum/showt...t=caster+angle


    Chop saw notching 101 (With pictures
    )
    http://pirate4x4.com/forum/showthread.php?t=456800




    Clutch Master by RocKrawler

    Clutch Master Cylinder Bleeding Instructions
    I had a biatch of a time when I replaced my clutch master trying to get the darn thing bled. No matter how much I bled it, the pedal was still a sponge. After placing a call to a buddy who works at a Toyota wrecking yard, his mechanic gave me this quick tip and it worked perfect the first time, even if you didnt bench bleed it before bolting it up to the firewall:

    1.) Adjust the bracket that pins to the clutch pedal so that it has about 1/4" free play
    2.) Fill the Clutch Master cyl resevoir ( duh )
    3.) Open the bleeder valve at the slave cylinder ( on the bellhousing for newbies, pass side, follow the hydraulic line from the clutch master down, you'll see it ) and without pumping the pedal, just let it drain until the resevoir is about 1/2 empty.
    4.) Close the bleeder and fill the resevoir
    5.) Have someone pump the clutch 5 times and hold, open the bleeder at the slave & bleed the system, closing the valve before fluid flow stops ( again for newbies )
    6.) Repeat step 5 until there is no more air bubbles when you bleed the system.

    If you followed the directions, you should have noticable clutch within 3 bleeding cycles, and be done within 6 cycles, whether or not you bench bled the clutch master before installing.


    Combination Turn Signal & Parking Light
    http://www.off-road.com/trucks4x4/ar....jsp?id=186224




    Cone Washers

    Cone Washers for Aisin or Asco Locking Hubs - 42323-60010
    Cone washers for solid axle steering arms - 42323-60020

    Cone washers are the washers that are behind the nuts holding on Toyota wheel hubs and steering arms.
    Cone washers are a pain in the a$$. Anyone from the dry areas of the southwest will tell you that a good smack on the stud will loosen them up. If you are in or near the Midwest... forget that.

    Using one or all of the following (most likely all) you should be able to get them off.
    • Soak it in something like PB Blaster
    • Put the nut on the stud and hit the nut with a brass drift and hammer
    • Use an air chisel - being careful of studs etc
    • Wedge a screwdriver or similar into the small slit of the washer
    • Beat the hub housing like a red-headed step child with a hard plastic or rubber mallet. If worst comes to worst (and if you are in the Midwest it probably will) then you can try hitting the hub housing itself with a small sledge hammer. At this point you will want to hit it with one anyway. The trick is not hitting hard enough to damage it.

    I (toy4crawlin) have heard to apply "Anti Seize" to cone washers to prevent them from sticking.


    Crossmembers - Transfer case / T-case
    Homemade, Aftermarket, Rotated, Flatbelly, High clearance, etc...
    http://www.pirate4x4.com/forum/showthread.php?t=634019
    Last edited by knixen; 04-03-2009 at 03:08.
    used to have a runner...


    "I used to go missing quite a lot... Miss Canada, Miss United Kingdom, Miss World." —British soccer bad boy George Best

  2. #2
    Fotograf knixen's Avatar
    Join Date
    Jan 2007
    Location
    Tromsø
    Posts
    4,195

    Default

    Continues.....
    OEM SA Front Wheel Studs
    ________________________________________
    Differentials – Gearing

    Gearing..... with a 4 banger and single case
    stock 4.10= 31 or smaller tire
    4.88=33 inch tire
    5.29= 35 to 38 inch tire.
    5.71= NOT RECOMMENDED FOR REAL OFFROAD USE

    Originally posted by DSI
    ----------------------------------------------------
    83-older 4.11 diff's are 37/9 and are 8in 4cyl style diff's, in 84 they switched th the 41/10 ratio, any time you have more teeth to a pinion the stronger the diff will be, reason being: more tooth contact/more teeth contacting the ring gear at one time.
    This is the same reason 5.71's are very weak, 6 teeth, 5.29's have 7, 4.88's and 4.38's have 8, 4.56's have 9 and 411's have 9, 410's have 10, and 390's have 10
    ----------------------------------------------------

    Originally posted by TNToy
    ----------------------------------------------------
    If you have the axle code of your vehicle, it is easy to find out what size differential, what ratio, and what pinion set-up you have. This will also help if you are hunting for a particular unit off another vehicle. The axle code is in the vehicle ID plate under the hood or drivers door. The axle code is 4 digits: a letter followed by 3 numbers.

    Example: G292 = 8.0" 4.10 final ratio 2 pinion
    Code:
    1ST R&P SIZE 2nd/3rd R&P RATIO 4th DIGIT PINION SET-UP
    F = 7.5" 07 = 3.900 2 = 2 pinion
    G = 8.0" 08 = 4.110 3 = 2 pinion LSD
    10 = 4.375 4 = 4 pinion
    14 = 4.875 5 = 4 pinion LSD
    25 = 4.556
    28 = 4.300
    29 = 4.100
    31 = 3.91
    38 = 3.42
    43 = 3.56
    54 = 3.90
    66 = 3.07
    .
    .
    Code:
    Ratio Ring/Pinion Color Crawl:Ratio
    3.42 ...42/12... Purple ...31:1
    3.90 ...39/10... Red... ...36:1
    4.10 ...41/10... Pink.. ...37:1
    4.11 ...37/09... Orange ...37:1
    4.30 ...43/10... Blue.. ...39:1
    4.37 ...35/08... Green. ...40:1
    4.56 ...41/09... Yellow ...41:1
    4.88 ...39/08... White. ...44:1
    5.29 ...37/07... None.. ...48:1
    5.71 ...40/07... None.. ...51:1
    .
    .

    Differentials – Info

    General Toy diff info including identification with pictures.
    http://home.4x4wire.com/erik/diffs

    "LPH" (Long Pinion Head) vs "SPH" (Short Pinion Head). by Drew Persson
    http://www.pirate4x4.com/forum/showt...23#post1478223

    Myth Settled: 8.4, V6, 4cyl, ALL 8" - by Brian Ellinger
    http://www.pirate4x4.com/forum/showt...hreadid=228681

    Pluging ABS sensor hole in late model diffs
    http://www.pirate4x4.com/forum/showthread.php?t=587522

    Differential picture identification by 4RnrRick

    Toyota 4 pinoin 6 cylinder 8" diff (30 spline)
    http://www.4crawler.com/4x4/Images/Diff6cyl.jpg

    Toyota Land cruiser high pinion 8" diff (30 spline)
    http://www.4crawler.com/4x4/Images/DiffHP.jpg

    Toyota 4 pinion 6 cylinder 8" 3rd from a '96-00? 4Runner (30 spline)
    http://www.pirate4x4.com/forum/attac...&postid=436184


    Differential Mounting Differences Between Different 3rd Members
    http://www.pirate4x4.com/forum/showt...52#post5331552




    Differential - Shaved, Trussed, and Armored Axle Collection
    http://www.pirate4x4.com/forum/showthread.php?t=456309 by TheBandit
    http://www.pirate4x4.com/forum/showthread.php?t=228464
    http://www.pirate4x4.com/forum/showthread.php?t=154306
    http://www.pirate4x4.com/forum/showthread.php?t=93356


    Differential Stud Upgrades - BEEF!!
    http://www.pirate4x4.com/forum/showthread.php?t=485834


    Doors - Quick Release Hinges / Removable Doors

    Info provided by Wheelie_Pete
    To get the old factory pin out without a fuss, cut it in half as it sits in the hinge, then take a cold chisel and start tapping around the edge of the top of the pin. (The hinges should be removed from teh vehicle first.) This should start to pry the pin upwards, then, when you clear the swege marks on the pin you can just pull it out. Repeat for the bottom half.
    If you manage to cut your hinges and then force out the stock pin without fawking up the brash bushing, then you can use a 5/16 (.3125") dia. x 2" long grip length pin perfectly. The stock door hinge bushings are 8mm (0.315" dia). My passanger's door hinges worked out this way and it works awesome! This works so well I can hardly believe it. The pin is upside down on the top hinge because there isn't enough room to drop it down through the top due to the shape of the door's edge. A sharp eye will notice that the lower bolt head on the door's half of the hinge is ground down. This is so you can clear the pin's shoulder by the bolt. It had to be done to get a straight up shot for the pin. Also when doing it this way you can retain the factory brass bushing which will keep the door tight and have that OEM fell. My driver's door's brass bushings in both hinges cracked when we tried to pull the stock pin so we had to drill them out to 3/8" and use a 3/8" Pin or bolt with the head ground down. This eventually wears on the hinges and Ifinally ended up replacing them with some I could use a 5/16 pin in.

    Info provided by NoBrainR
    I used spring pins and left the stock bushings in. About 30 seconds to take a door off and 2 minutes to put it back on with no help and perfect alignment each time. Had to grind a little off one bolt head per hinge.

    Info provided by TNToy
    Here's the route I went. It cost me six dollars. I carry a 12MM ratcheting box wrench ($6 from Sears) in the glove box. Prefect fix on the bolts without rounding them off... a non-ratcheting type tends to twist sideways and round off the bolt slightly with each use. Then you just do what's in the pic. It lets you loosen both bolts 2-3 turns and pull the door right off.

    Info provided by JeepRecoveryTeam & Krusty
    Just cut the hinge pins and the door simply lifts off !!!!-------- no bolts ,no pins , and no hastle---- 10 seconds off- 15 seconds on ! full doors and a set of .5 doors------on and off 'instantly' !

    Info from Mr Stubs...
    Loosen the top bolt and remove the bottom bolt.
    This will allow for the door to be set and hung while you remove/replace the bottom bolt while quick changing doors.



    Doors - Ultimate Collection of Half Door Pictures
    http://www.pirate4x4.com/forum/showt...ight=half+door
    Removable Doors with electric windows.
    http://www.pirate4x4.com/forum/showthread.php?t=775832


    Drain Plugs - Low profile

    Toyota Part #'s
    90341-18021 Plug w/magnet $1.50-$2.00/ea.
    12157-10010 Gasket, diff plug $0.75/ea.
    90430-18008 Gasket, tranny/transfer $1.00/ea.

    These plus will fit Toyota 7 1/2", 8" & 8.4" Axle housings. They also fit Toyota Chain and Gear Driven T-cases and Transmissions. they even fit Samuri T-cases. But they will NOT fit Samuri Trannys.



    Drawing files
    T-case mount like FROR by BRAD D
    http://members.shaw.ca/lhnatishin/Tmount2.dxf




    Driveline - How to make a Square Shaft
    http://www.pirate4x4.com/forum/showthread.php?t=90517
    http://www.ehow.com/how_4475628_buil...riveshaft.html



    Driveline - Heavy duty DIY Material
    A toyota driveshaft end has a machined OD of 2.435".
    2.5'' Sch. 40 pipe. is 2.875" OD x .203" thick which is almost 1/4'' wall and is a good fit for the toy yokes. You just have to use an endgrinder or the like to knock the seam down in the pipe. Using the pipe to retube is good for rear shafts or if you have links and don't need all the slip of a square shaft. (also slides on rocks better than square) This is a cheaper alternative to the strange sized 2 7/8" x 7/32" wall DOM tubing which can also be used for a DIY driveline.

    Driveshaft Tech

    Driveshaft Shortening 101
    http://www.pirate4x4.com/forum/showthread.php?t=485542

    Driveshaft 401 by BillaVista
    http://www.pirate4x4.com/tech/billav...aft/index.html




    Driveshaft Yokes / Flange patterns
    http://www.pirate4x4.com/forum/showt...46#post4201146
    http://www.pirate4x4.com/forum/showt...49#post4200349
    And this is the easiest way to make a different bolt-pattern driveshaft fit your current flanges: Rotate the driveshaft 45 degrees and drill new holes.

    More flange pattern measurements

    Flange Pattern dimensions for
    My truck 1989 Extra cab V6 factory 2 peice drive shaft
    tcase/ujoint > 60mmx x60mm x 10mm CSB/ Dual Cardon Joint 60mm x 60mm x 10mm > Rear dif/Ujoint 60mm x 60mm x 10mm

    Flange Pattern dimensions for
    My Brothers truck 1993 Extra cab 22RE factory 2 peice drive shaft
    tcase/ujoint > 60mmx x60mm x 10mm CSB/ Dual Cardon Joint 60mm x 60mm x 10mm > Rear dif/Ujoint 60mm x 60mm x 10mm

    Basically I was worried that the flange pattern on the stock REAR Cv would not work with a triple drilled flange at the tcase. Seems like they will match up since the triple drilled flange has a 60x60x10 pattern.
    __________________

    Dual Tranny Setup and Adapters
    http://www.pirate4x4.com/forum/showthread.php?t=698521
    http://www.pirate4x4.com/forum/showthread.php?t=132841



    E-Brake - Cheap Cable Fix by OOP’s
    http://www.pirate4x4.com/forum/showt...501#post384501




    ECU Compatibility
    http://www.pirate4x4.com/forum/showthread.php?t=247846





    Electrical Questions

    More than you want to know…….
    http://www.autoshop101.com/autoshop15.html

    killer place to get all kinds of electrical goodies: (by Old Scout)
    http://www.waytekwire.com/index.htm




    EFI System – Trouble codes

    The older Toyota fuel injection systems are analog systems based on Bosch L-jetronic.
    Around the mid-80's the Toyota TCCS took over, it is a (8031/8051)
    microcontroller based digital system using in-chip ROM.
    That means there is no separate ROM chip which could easily be
    read and replaced for tuning purposes...
    Later versions use more powerful microcontrollers.
    The TCCS systems use L-jetronic, MAP, hot-wire and vortex
    type air flow meters depending on application.

    OBDI Toyota EFI troubl
    e codes:
    http://www.off-road.com/toyota/tech/codes/

    OBDII Toyota EFI troubl
    e codes:
    http://www.troublecodes.net/Toyota/
    [url]http://www.yotatech.com/showthread.php?t=76363[/url]


    Engine Upgrades and Tech-22re, 22
    rte, 22r
    MSD Install
    22R - http://www.pirate4x4.com/forum/showthread.php?t=428313
    22RE - http://www.pirate4x4.com/forum/showthread.php?t=436107

    Cam info - 22R / 22RE
    / 22RTE
    [url]http://www.pirate4x4.com/forum/showthread.php?t=587414[/url]

    22RE TPS Cross Reference by Drew
    Persson
    http://www.pirate4x4.com/forum/showthread.php?t=272959

    Fuel Injector cross r
    eference
    http://www.pirate4x4.com/forum/showthread.php?t=587421

    22RE alternator upgrades by Al
    abamatoy
    http://www.pirate4x4.com/forum/showthread.php?t=587456

    ATTN: Tim@DOA, what are our most common mistakes when we wrench on our engines?
    [url]http://pirate4x4.com/forum/showthread.php?t=537816[/url]




    ENGINE / MOTOR S
    WAP INFO

    Official Toyota motor swap
    thread-
    http://www.pirate4x4.com/forum/showthread.php?t=206806

    22R to 22RE
    swap FAQ
    http://www.pirate4x4.com/forum/showthread.php?t=316661

    5VZ-FE / 5VZE / 3.4L V6 Toy
    ota Swap
    http://www.pirate4x4.com/forum/showt...t=137361&pp=25

    3RZ s
    wap tech
    http://www.pirate4x4.com/forum/showthread.php?t=475469

    Marlin Crawler
    3RZ FAQ
    http://board.marlincrawler.com/index.php?topic=19275.0

    3rz wiring inf
    ormation
    http://www.pirate4x4.com/forum/showt...ght=3rz+wiring

    VW/Toy Dies
    el swaps
    http://www.pirate4x4.com/forum/showthread.php?t=574419

    4.3L Swap FAQ version 2.0 by Lo
    wtorious
    [url]http://www.pirate4x4.com/forum/showt...ghlight=3l+faq[/url]

    3.0L-V6(3VZE) To 3.4L-V6(5VZFE) Engine Co
    nversion
    [url]http://www.pirate4x4.com/forum/showthread.php?t=587453[/url]





    Exhau
    st Studs
    This is fairly basic, but it is info that is helping me out right now. Seems to be a common problem. It took me a long time to find the post.
    It's about stripped exhaust studs and a Heli-coil kit that NAPA sells specifically for repairing Toyota heads.

    exhaust head heli coil info
    ****************************************
    Description: NAPA Balkamp HeliCoil Metric thread repair kit
    Size: M10x1.25
    Part#: 7703020
    ****************************************
    Description: HeliCoil Thread Repair Metric Kit
    Size: M10x1.25 - 12 Inserts
    Part#: HEL-5543-10
    See: [url]http://www.pirate4x4.com/forum/showt...t=exhaust+stud[/url]



    E
    xo Cages
    Lots of pictures of exo cages here!
    http://www.pirate4x4.com/forum/showthread.php?t=95564
    Thru body design exo cages
    [url]http://www.pirate4x4.com/forum/showthread.php?t=761629[/url]




    Factory Service Manuals (FSM)
    - Online
    Toyota & Ebay is a great spot to find these... otherwise look here:
    http://www.pirate4x4.com/forum/showthread.php?t=329685
    or 4or a $10, one day subscription you can download all the FSM’s for your rig.
    http://techinfo.toyota.com/index.html
    Links to free FSM's (Factory Service Manuals)
    [url]http://www.ncttora.com/fsm/index.html[/url]



    Fiberglass pan
    el links
    http://www.bgfiberglassusa.com/index.html
    [url]http://www.actionsalvage.com/truckbeds.asp[/url]



    Flat Towing
    a Toyota <-- Must disconnect rear driveline!
    Quote:
    Originally Posted by Marlin Crawler
    On all auto chain driven and manual gear driven t/cases, if it is towed in two wheel drive, the output shaft will turn, but there will be no way for the oil at the bottom of the case to get to the top where the output shaft is. On the chain driven cases, the input shaft turns the planetary housing which drives the oil pump. Gear driven cases use the input gear and low range gears to throw oil on the inside of the housing that collects the oil via gutters and directs it to the rear of the case by gravity. Both style of cases, must have the input shaft spinning to lube the output shaft, speedo gears, and rear seal of the t/case. The rear driveshaft must be removed.
    Marlin
    Last edited by knixen; 04-03-2009 at 03:14.
    used to have a runner...


    "I used to go missing quite a lot... Miss Canada, Miss United Kingdom, Miss World." —British soccer bad boy George Best

  3. #3
    Fotograf knixen's Avatar
    Join Date
    Jan 2007
    Location
    Tromsø
    Posts
    4,195

    Default

    And More......
    Filter Charger for 22RE - Cone Filter adapter for AFM from the wrecking yard
    http://www.pirate4x4.com/forum/showthread.php?t=308855


    Firewall Tubing
    Firewall Tubbing 79-83 Toyota's
    http://www.pirate4x4.com/forum/showthread.php?t=587505




    Formula Toy Info & FAQ Hendrix Motorsports
    http://www.pirate4x4.com/forum/showthread.php?t=449917

    Frame Dimensions:
    Frame Dimensions: 79-83
    http://www.pirate4x4.com/forum/showthread.php?p=8763381

    Third Generation frames
    http://www.pirate4x4.com/forum/showthread.php?t=599542

    85 Frames Thanks Budbuilt
    http://www.yankeetoys.org/Documents/85Frame.gif
    http://www.yankeetoys.org/budbuilt/i...85%20frame.jpg


    Front Axle - IFS Hub Body & Vented Rotor Swap Options
    Best Thread according to JWS-
    http://pirate4x4.com/forum/showthrea...15#post2423615

    http://www.pirate4x4.com/forum/showt...b+vented+rotor
    http://www.pirate4x4.com/forum/showt...b+vented+rotor
    http://www.pirate4x4.com/forum/showt...b+vented+rotor



    Front axle – Knuckle Rebuild Kits

    http://www.allprooffroad.com
    http://www.jtoutfitters.com
    http://www.marlincrawler.com
    http://www.sky-manufacturing.com

    Timken Wheel front wheel bearing part numbers for 79-85 front axle:
    Front wheel outer LM102949 & LM102910
    Front wheel inner JLM104948 & JLM104910

    Trunion/Kingpin/Knuckle bearing part numers, 79-85 front axle:
    Toyota #90366-17001-77
    KOYO 30303D
    SKF part# 30303j2

    Inner axle seal, 79-85 front axle: by KS Toy
    Timken 710070
    BCA 710070
    FM 710070
    Toyota 90311-35032
    CR 12810

    Knuckle stud parts
    42323-60020 Washer, Cone
    90170-12005 Nut, Hexagon
    90126-12005 Stud, Hex Lobular

    Exploded diagram of front axle from JTOutfitters website:



    Ref: Spindle nut size is 54mm/2-1/8" socket











    Front Axle Perches – 3/8” Spacer
    Toyota front axles need a 3/8 inch spacer on driver side to make the truck sit level since the driver side perch is 3/8” lower than the passenger side perch since its mounted half way up the diff. If you do a spring swap using non-Toyota Specific Springs, this spacer should be added. The most common way to do this is to weld a piece of flat bar to the driver side perch.



    Front Axle, Picture Thread, Toyota 8"
    http://www.birfield.com/~morgan/tech/axle/

    Front Axel- Ultimate Toyota Front Upgrades-
    http://www.pirate4x4.com/forum/showthread.php?t=764615

    Fuel Cell Info
    http://www.pirate4x4.com/forum/showthread.php?t=293628



    Fuel Filter Fitting
    Aeroquip P/N: FCM 1070 is a bajo fitting hose end that screws directly in to a 22re fuel filter for -6 (3/8") hose or 'Summit' AER-FBM1070 or 'Summit' #EAR-807691ERL.


    Full Float Rear- Toyota Dually Axel tech-
    http://www.pirate4x4.com/forum/showthread.php?t=766576
    Full Floater Conversion-
    http://www.pirate4x4.com/forum/showt...ota+full+float
    http://www.pirate4x4.com/forum/showt...ota+full+float


    Gearing Calculator-
    For anybody that wants to see how many RPM's their turning with a given transmission/transfer case/axle ratio/tires, here's a great calculator. I made my own a few years ago, but this one is much nicer.
    http://www.grimmjeeper.com/gears.html
    __________________
    1991 Toyota Pickup 4.3L 700r4, flat bed, axles the usual.... and so on
    used to have a runner...


    "I used to go missing quite a lot... Miss Canada, Miss United Kingdom, Miss World." —British soccer bad boy George Best

  4. #4
    Fotograf knixen's Avatar
    Join Date
    Jan 2007
    Location
    Tromsø
    Posts
    4,195

    Default

    And The Saga Continues
    Head Gasket Replacement by 85runnerAZ
    http://www.pirate4x4.com/forum/showt...83#post1748083


    High Lift mount ideas and safety
    http://www.pirate4x4.com/forum/showthread.php?t=755469

    HiLift Safety Tip: Use a limit strap or chain by TheBandit

    Here is a tip anyone with a hi-lift jack should be aware of. Always carry a strap or chain with you. Why? You can use it to limit the droop of the suspension when changing tires/axles/etc.

    How many times have you seen a vehicle lifted near the maximum height of the jack just to get the tire off the ground? This is incredibly dangerous! It puts the vehicle in an unstable position and people around/under the vehicle at uneccessary risk.

    To avoid hurting someone, attach a chain or strap between the axle and frame to limit droop. You can do this while the vehicle is still on all four tires. As you jack from the body or frame, the axle will droop until the limit chain/strap tightens.

    Be aware of brake lines and other vulnerable components when routing your limit strap/chain. Also, make sure whatever chain/strap you carry on the trail is adjustable in case the suspension is articulated before jacking.


    Horn Tech
    http://www.pirate4x4.com/forum/showthread.php?t=318491



    Horsepower – More Power

    Thanks to DRM for saving this, and Tim for giving the advice.

    Originally posted by DRM
    -----------------------------------------------------------
    "Ok ready, first pull off the efi fuse for a couple of seconds, then reinstall it. Grab some Autolite #65 plugs, and side gap them at .048. Set the valve clearance to .011 cold. Install the factory carbed thermostat {Pappy: it's a 180* vs. 190*). Adjust the AFM 3 teeth rich (under 5000 a.s.l.). Start the motor, let idle till you reach operating temp. Set the timing at 16* "not short circuted," {Pappy: about the same as 8* shorted} then take it for a putt, re check the timing, and enjoy. Leave the airbox alone, for it's not a cause of starvation on a stocker, and don't worry about the muffler for now. If you're going to modify the exhaust, start with a header, and 2.5" headpipe."

    A follow-up from later that day:

    "... you pull the EFI fuse to start the ECU's regathering of fuel mixture readings, because you are altering them via the AFM. The #65's are a hotter plug, and will in this case create a more efficient burn. You WILL NOT detonate when the timing is set 16* NOT SHORT CIRCUTED, because the end reading when short circuted will be 8* advanced. The afm adjustment enrichens the motor aproximately 3cc. This is necessary due to the timing advance, which requires a proper mixture."

    I found the AFM 3 teeth to be too rich for my high desert home (driveway is 5200 ft) and have backed it down to 1 tooth rich.
    -----------------------------------------------------------



    Hydraulic Steering Bleeding Instructions
    http://www.pirate4x4.com/forum/showt...95#post7319895
    http://www.pirate4x4.com/forum/showthread.php?t=542215


    Hydraulic Steering Tech - Assist
    http://www.pirate4x4.com/forum/showthread.php?t=617039



    Hydraulic Steering Tech - Full Hydro—OOPS set up
    http://www.pirate4x4.com/forum/showt...ght=full+hydro



    Idle Drop

    "It's an 85 xcab efi. When I hit the brakes my idle drops off 500 rpms or so then recovers, over and over again. It dosen't happen when It's warming up, just when hot."

    "I would bet you that your idle is set to high. Sometimes the screw works loose with vibration. If your idle is at like 1100, it's too high. With the engine warm, try lowering the idle at the intake manifold to about 750 or so. That will probably solve your problem. Mine was doing the same thing last week after the new header. Adjusted the idle and it's fine. "

    "The EFI computer receives a signal from the brake circuit that tells it that the brakes are being applied. This causes the computer to shut off the injectors if the RPM's are over a certain level and the engine is in "closed loop" as engine power should not be needed if the brakes are being applied.I believe the set point for the injector cut out is 850 to 900 RPM. This is what causes the surging - your idle RPM is too high, when the brakes are applied the injectors are cut out until the RPM's drop below this level. The engine then run's again. This only happens when the engine goes into "closed loop" so this will not happen when the engine is at a higher idle speed warming up. I am willing to bet your idle speed is around 1000 RPM when this happens. To fix this problem, simply adjust your warm idle speed to 750 RPM as per the factory. "




    Ignitor and Coil Bypass for Cheap
    http://www.pirate4x4.com/forum/showthread.php?t=179253




    LED’s
    How to wire up LED lights for taillights?
    http://www.pirate4x4.com/forum/showthread.php?p=5329844




    Link suspension info
    The ultimate listing of the most important link suspension posts.......

    1-link
    http://www.pirate4x4.com/forum/showthread.php?t=235977

    1/4 eliptical
    http://www.jeepaholics.com/tech/quarterellip/

    1-link
    http://www.pirate4x4.com/forum/showthread.php?t=235977

    3-link

    front
    http://www.pirate4x4.com/forum/showt...highlight=link

    rear
    http://www.pirate4x4.com/forum/showthread.php?t=477922

    4-link
    http://www.4wheeloffroad.com/techart...t_2/index.html
    http://www.pirate4x4.com/forum/showt...ink+anti+squat

    Coil spring specs
    http://www.pirate4x4.com/forum/showthread.php?t=723229

    ExcelCAD - Awesome Link design Program
    http://www.gregblanchette.com/pages/1/index.htm

    THE GOD OF SUSPENSION...[for those of you who don't know]
    http://www.pirate4x4.com/forum/showthread.php?t=7503

    LINK SUPSENSIONS FOR DUMMIES?
    http://www.pirate4x4.com/forum/showthread.php?t=168577

    New Version of my 4-link Analyzer & Request for Help
    http://www.pirate4x4.com/forum/showt...hreadid=204893

    Rear link thread
    http://www.pirate4x4.com/forum/showt...highlight=link





    Lockers - Whats Better?
    http://www.pirate4x4.com/forum/showthread.php?t=504856




    Locking Hub Upgrades

    Bigger Studs
    http://www.pirate4x4.com/forum/showt...hreadid=209057

    Stronger Studs http://www.frontrangeoffroadfab.com/nfoscomm/catalog/
    http://www.pirate4x4.com/forum/showt...=stronger+stud

    6 pin install on the hubs http://www.hendrixmotorsports.com/
    http://www.pirate4x4.com/forum/showt...hreadid=233101

    4340 Chromoly Toyota 30 Spline Drive Flange by Longfield
    http://www.pirate4x4.com/forum/showthread.php?t=519033

    Can you convert a 27 spline IFS locking hub to a 30 spline SA locking hub?
    http://www.pirate4x4.com/forum/showthread.php?p=5979707

    Longfield's Axle/Hub/Shaft Breaking Machine Results
    http://www.pirate4x4.com/forum/showthread.php?t=467075

    Longfield - 27 vs. 30 Spline Chromo
    http://www.pirate4x4.com/forum/showthread.php?t=309632



    Martack - See 'Birf Stuff' above for more info on this....

    The easiest way to find the correct location for a Martack is to put tape on the spines of the axle shaft and insert the axle into the housing while watching the seal location. And keep moving the tape until you found the correct position.
    http://www.pirate4x4.com/forum/attac...postid=1537731

    Also note that after tacking the splines you wil have to carefully grind them doen flush so the axle will slip into the spider gears/locker all the way to the tack. Another way is to grease the splines but for me that has never worked as good as using tape. You want to place the tack weld so the axle can not slide into the diff to causing the seal to leak diff fluid into your knuckle. This is also used with aftermarket Birfs so you can remove the outer most clip to add in removal of the axle from the birf n the case of trail breakage.

    Another think tha tis important to note is that you SHOULD measure this distance on you axle and not following any one elses dimensions becasue there are too many variables to only use on tack weld location for all set-ups.

    Quote:
    And here is the Camo Method.

    This verson allows the axle and Birf assmbly to float a bit on the brass bushing inthe spine, on the splines in the star of the birf and the splines in the diff to tolerances and expansion or contraction due to the change in temperature.



    More Reference Links:
    http://www.pirate4x4.com/forum/showt...67#post2913767



    Motor Mount Tech

    Heres some great info on how to "bolt" your motor mounts to keep them from getting trashed by the torque produced from a crawler box.
    ref: http://www.pirate4x4.com/forum/showthread.php?t=154338

    The other common way to save the motor mounts is to chain them down.

    A common way is shown below:



    As a side note aftermarket poly bushing motor mounts create a LOT of vibration and is seems that about 50% of these people that buy them for a Daily Driver end up removing them and reinstalling stock ones. The motor mounts that I refer too are ones sold by Rockstomper or LC Engineering which look symiliar to this homemade one [Thanks Chrisf]. Now if they are going on a trail only rig, I hear they work awesome.

    Aftermarket motor mounts parts numbers by obex26
    Well in the process of getting aftermarket motor mounts since the cost is between 25-50 dollars versus 155-180 from the stealership I learned the hard way about part numbers and applications so I thought I would share it with everyone else. Most checker, kragen, pep boys, autozone or whatever is near you will carry an aftermarket brand called anchor. The part number for the 4 cylinder application is 8612 and the 6 cylinder application is 8614. The truck and 4runner for years 84-86 may use the part number for the 6 cylinder application even though it has a 4 cylinder engine in it. I spent two days looking for motor mounts (limited local stock on a weekend) It appears that before the 6 cylinder motor was introduced to the truck line they were already using the motor mounts. It also is a hit and miss with the truck years that the turbo and V6 were available. It seems that the 2WD trucks actually use the part number 8612 and 4WD whether its a 4 cylinder Turbo or V6 use the part number 8614.

    Also to add to the above info, First gen and second gen motor mounts are different because the hole spacing on the frame is different along with the shape of the six sided base plate..

    Other After Market Options:
    There are many Poly and bushing type motor mounts. Extreme vibrations from these mounts are often reported. Usually not recommended for daily driven vehicles.

    Northwest Offroad


    Rockstomper
    used to have a runner...


    "I used to go missing quite a lot... Miss Canada, Miss United Kingdom, Miss World." —British soccer bad boy George Best

  5. #5
    Fotograf knixen's Avatar
    Join Date
    Jan 2007
    Location
    Tromsø
    Posts
    4,195

    Default

    Oil Filter by deepstealth

    A good oil filter is toyota 90915-YZZD3 (old part number: 90915-20004) it is slightly larger, they use it on tundras, lexus' and and cost about 6 bucks each.

    More info provide by deepstealth:
    Yeah, theyre gonna discontinue the -20004 and i hear rebadge it and sell for ten bucks as the "TRD" uber special filter. not worth it, for that money you can get an sdf-15 from amsoil, which is even better but expensive overkill for most rigs. the yzzd3 is NOT a high quality filter--take one apart & compare to the -20004, the difference is pretty obvious--it's pretty much just a basic cheap-o filter, but twice as much as a fram. the -20004s can still be purchased (in cases), and you'll usually get a bulk discount.




    Oil Pan swap for 3.0V6 to T100 oilpan swap for SAS and histeer
    http://www.pirate4x4.com/forum/showthread.php?t=23993




    Oil Pressure Guage
    The OEM cluster gauge is not very accurate and it the FSM shows the following picture:

    Factory numbers for both the 4 & 6 cylinder engines
    Oil Pressure @ Idle - 4.3 psi Minimum
    @ 3000 rpm - 36 - 71 psi




    On Board Air (OBA)
    See "York" below for tons of info.


    PARTS- Supplier of used and new, salvage yards, etc... also who to avoid!!!!!!!!!!!!!!!
    http://www.toyodiy.com/parts/
    http://www.davezoffroadperformance.com/
    http://www.pirate4x4.com/forum/showthread.php?t=682314

    STAY AWAY FROM TAP, unless u enjoy getting bent over!!!!!!!!
    Ref:http://www.pirate4x4.com/forum/showthread.php?p=21403


    Part Numbers - Ultimate List of Toyota Part Numbers by 4x4wire.com
    http://www.4x4wire.com/forums/showfl...5&o=14&fpart=1




    Pictures - TONS
    Pics of your favorite Toyotas
    http://www.pirate4x4.com/forum/showthread.php?t=144215

    Pics of your Favorite Buggy's and Truggy's
    http://www.pirate4x4.com/forum/showthread.php?t=222645

    Toyota Flex pictures
    http://www.pirate4x4.com/forum/showthread.php?t=307956

    Pictures of favorite 4runners
    http://www.pirate4x4.com/forum/showthread.php?t=254023
    http://www.pirate4x4.com/forum/showthread.php?t=361172

    Pictures of First Gen's
    http://www.pirate4x4.com/forum/showthread.php?t=638383

    Full width picture thread
    http://www.pirate4x4.com/forum/showt...&highlight=ton

    Dovetailed pics
    http://www.pirate4x4.com/forum/showthread.php?t=474701

    *Official* Toyota Flatbed Thread
    http://www.pirate4x4.com/forum/showthread.php?t=98472

    Before and After Pic Thread
    http://www.pirate4x4.com/forum/showthread.php?t=575684




    Pitman Arms - Dimension of other arms
    http://www.pirate4x4.com/forum/showthread.php?t=593367
    http://www.pirate4x4.com/forum/showthread.php?t=294202




    Pitman Arm Removal / Swap - How to
    http://www.pirate4x4.com/forum/showthread.php?t=511091




    Plenum Conversion and How to Remove Unwanted Vacuum Lines - Lots of 22RE Photos
    http://www.pirate4x4.com/forum/showt...8&page=2&pp=25



    Profield Information........
    http://board.marlincrawler.com/index.php?topic=7534.0
    Pay attention to the posts by Chris Gieger......



    Propane Conversion, 22R
    http://www.pirate4x4.com/forum/showthread.php?t=379633 by KYOTA
    http://www.pirate4x4.com/forum/showthread.php?t=490223 by brimy311


    Power Inverter Thread- for all you 110v needs
    http://www.pirate4x4.com/forum/showthread.php?t=549810

    Power Steering Box - Info

    How to rebuild it
    http://web.archive.org/web/200503220.../taco/box.html

    Steering Box rebuild kit PN 04455-35080
    http://www.pirate4x4.com/forum/showthread.php?t=587519

    How to Tap it for Hydro Assist
    http://www.wildyoats.com/hydraulic_assist_tech.htm
    http://board.marlincrawler.com/index.php?topic=10579.0


    Power Steering Box Location, Moving it Forward by Bones
    Since this has been on numerous threads, I may as well post it here. Here's an IFS steering box moved as far forward as I could (2.5"~) and hacked the radiator support to boot. Ref: http://www.pirate4x4.com/forum/showt...t=steering+box
    More pictures of mounting the power steering IFS boxes here:
    http://www.pirate4x4.com/forum/showthread.php?t=587517
    http://www.pirate4x4.com/forum/showthread.php?t=424669



    Power steering box identification
    http://www.pirate4x4.com/forum/showthread.php?t=587515



    Power Steering Box AN-Fittings
    http://www.pirate4x4.com/forum/showthread.php?t=617050
    High Pressure Port - 16 x 1.5 MM Inverted Flare to #6 JIC Male adapter, Toyota - 'PSC Motorsports' #PSC-SF06 or 'Summit Racing' #EAR-9919DFJERL
    Low Pressure Port - 17 x 1.5 MM Inverted Flare to #6 JIC Male adapter, Toyota - 'PSC Motorsports' #PSC-SF07


    Power Steering Flush
    http://www.pirate4x4.com/forum/showthread.php?t=588900

    Power Steering Hose Part Numbers- Stock Application-
    Stock power steering high pressure hose PN's:

    '85 4WD NAPA: NPS73354 $27.99
    VATO Zone: 71260 $25.99
    '83 4WD VATO Zone: 71171 $25.99
    Schucks: 71171 $37.93

    The difference's between the two are the '83 has a 45 degree bend and long stem into the box and a 90 degree bend on the pump end and the '85 has a short 90 on the box side and two oposing 90's on the pump side


    Power Steering Pump Mod - Removing the restrictor plate
    http://www.pirate4x4.com/forum/showt...hreadid=167299
    http://board.marlincrawler.com/index.php?topic=10579.0


    Power Steering Pump - High Flow TC style mounting
    http://www.pirate4x4.com/forum/showthread.php?t=571624
    http://www.pirate4x4.com/forum/showthread.php?t=630765



    Power Steering Reservior
    www.Speedwaymotors.com has a power steering resivoir that is a perfect fit for this set up. $24.95
    It is P/N 91032876-STD-10. It has a -6 inlet and a -10 outlet.
    this fits the power steering pump inlet well.
    Tripling the size of the Toyota power steering reservoir
    http://www.pirate4x4.com/forum/showthread.php?t=579700


    Rust Repair Panels / Replacement Sheetmetal
    http://www.pirate4x4.com/forum/showt...hreadid=234917


    SAS Pics and Dimensions thread
    http://www.pirate4x4.com/forum/showthread.php?t=321699
    Low Lift SAS Thread--
    http://www.pirate4x4.com/forum/showthread.php?t=674078


    Seat Tech- Replacements and Junkyard swaps
    http://pirate4x4.com/forum/showthread.php?t=555099
    http://pirate4x4.com/forum/showthread.php?t=367208

    Shock Mounts - Ford
    Ford Part #E5TZ-18183-A



    Shower, On-board Shower Tech
    http://www.pirate4x4.com/forum/showthread.php?t=579698
    http://www.pirate4x4.com/forum/showt...threadid=80252



    Smog/Emissions
    Try out this Lambda calculator using your emissions test info. This will help you determine if you are running rich, lean, or stoichemetric.
    http://www.smogsite.com/calculators.html#lambda
    Then use this article to understand how to use lambda to diagnose your failure
    http://www.byui.edu/Automotive/Lambda.pdf
    Some other good smog passing threads
    http://board.marlincrawler.com/index.php?topic=1119.0
    http://www.pirate4x4.com/forum/showthread.php?t=472825
    http://www.pirate4x4.com/forum/showthread.php?t=368727



    Spring Hangers - Front - SAS
    http://www.pirate4x4.com/forum/showthread.php?t=321699
    http://www.pirate4x4.com/forum/showt...threadid=76595



    Springs!
    ********************************

    44044 SPRINGS
    44044s are Rancho Jeep Wagoneer Lift Springs.
    Length: 47" (Length is eye to eye)
    Center Pin split (front/rear) 22.5"/24.5"
    Bushing: 2 3/4" & 3"
    Lift: 5.25 - 5.5" (Lift is approximate and uses 1.5" longer than stock shackles giving 3/4" of lift)
    Cost: $250 (Cost is for both sides incl. shipping/give or take)
    44044's do not (by themselves) move your axle forward. They are the same length on the front half as stock toys (22.5"). While they do move the axle forward because of the lift they provide (arch in spring), when they compress to the point that they are flat, it's the same. Estimated 1/2" of actual axle relocation forward.
    http://bbs.off-road.com/wwwthreads_u...ith%20dims.jpg

    ********************************

    ALL PRO OFFROAD SPRING LENGTHS by Chris Gieger
    Part Number, Overall Spring Length, Center Pin to Front*
    TOYFRONT5, 47 5/8", 22 1/2"
    TOYFRONT4, 46.1/2", 22 1/8"
    TOYFRONT5STK, 46 3/4", 23 1/8"
    TOYFRONT4STK, 45 5/8", 22 1/2"
    TOYFRONT3, 46", 21 1/2"

    ********************************

    CHEVY SPRINGS FAQ Probably most common rear lift springs!
    Everything you ever wanted to know about Chevy Springs!
    http://www.pirate4x4.com/forum/showt...threadid=20665
    If you actually have a question that is not answered there, that would be a great place to ask it so the answer is there for everyone else.

    ********************************

    REARS SPRINGS UP FRONT Probably most common front lift springs!
    Rears Up Front (RUF) FAQ: http://www.pirate4x4.com/forum/showthread.php?t=265669
    Stock toy rears move the axle forward 2" because they are only 20.5" on the front half where as a stock toyota front spring is 22.5". But you have to add a few leaves to the pack to make them stiff enough to hold up the front of the truck.


    ********************************

    WAGONEER / WAGGY SPRINGS
    These are stock Jeep Wagoneer Springs
    Length: 47" (Length is eye to eye)
    Bushing: 3"
    Lift: 3.5 - 3.75"
    Cost: $200 New, $60-$100 Used
    From JcWhitney.com:
    1976 - 1992 Jeep Wagoneer, Front Leaf Spring
    7 Heavy-duty Leaves #07ZX2048P $99.95 Ea
    5 Leaves #07ZX2047B $84.95 Ea
    The 7 leaf is supposed to be the ones you are looking for.
    Pinion angle can be an issue if you just bolt waggs to the stock location. If you have dropped hanger or dual cases the problem is lessened.

    ********************************

    Misc. Spring Information
    http://www.4x4spot.com/spring_swap_info.htm
    http://www.4x4spot.com/misc__spring_information.htm
    used to have a runner...


    "I used to go missing quite a lot... Miss Canada, Miss United Kingdom, Miss World." —British soccer bad boy George Best

  6. #6
    Fotograf knixen's Avatar
    Join Date
    Jan 2007
    Location
    Tromsø
    Posts
    4,195

    Default

    SR5 Gauge Cluster swap info
    http://www.pirate4x4.com/forum/showthread.php?t=236097
    http://www.pirate4x4.com/forum/showthread.php?t=209942




    Steering Arms - Adding Fifth Knuckle Stud or D44 Studs
    http://www.pirate4x4.com/forum/showt...65#post5752165
    http://www.pirate4x4.com/forum/showt...hreadid=186936
    http://www.pirate4x4.com/forum/showthread.php?t=326741
    http://www.pirate4x4.com/forum/showthread.php?t=550092
    http://www.pirate4x4.com/forum/showthread.php?t=394089



    Steering Column - Tilt/Wheel and Intermitent Wiper swap
    http://www.pirate4x4.com/forum/showt...48#post3574248




    Storage - additional storage in 4Runner under cargo area
    http://www.pirate4x4.com/forum/showthread.php?t=262253





    Thermostat Problem

    Question: “Why does my engine temp go all the way up to the red before it comes back down to the middle of the gauge after I start it up in the morning. It only does this when the engine is cold and once it warms up it seems to operate normally. Could it be as simple as a stuck thermostat?”

    Answer: (From Roger Brown’s Web Site - http://4crawler.cruiserpages.com/4x4...tml#Thermostat)

    “What happens on the 22R and 22RE engine, when the coolant goes through the heater core it gets cooled off enough that when it gets dumped back in on top of the t-stat it shuts it. Therefore the temperature in the engine continues to go up. The t-stat that I have mentioned has two valves in it, one at the regular temp. and one smaller on at a cooler temp. If the cool water shuts the big one, the smaller one stays open. All this happens because of the lack of a by-pass hose, which on other systems, keeps hot coolant running on the t-stat.”

    You can get the two-stage thermostat mentioned above from your local Toyota Dealer.
    Part Number: #90916-03070




    Tie Rod Ends, FJ-80
    These tie rod ends are the standard ones Aftermarket Companys use for the Toyota High Steer since they have the same taper as the mini trucks but they have a much larger 23mm x 1.50 threads. These are stock on 1991 thru 1997 FJ-80 Toyota LandCruisers relay rod ends.
    RH Thread - Napa #269-2854 or AutoZone #ES2854x
    LH Thread - Napa #269-2855 or AutoZone #ES2855x




    Tie Rod Ends, Mini Trucks
    Left Tie Rod End Differences by FreakAccident
    79-81 - Short, small threaded shaft, and the hole for the steering stabilizer is on the top part of the shaft. Approx. 5.5"s from where the threads start on the shaft to the center of the joint.
    82-83 - Long, small threaded shaft, and the hole for the steering stabilizer is on the bottom part of the shaft Approx. 6.5"s from where the threads start on the shaft to the center of the joint.
    84-85 - Long, large threaded shaft, and the hole for the steering stabilizer is on the bottom part of the shaft. Approx. 6.5"s from where the threads start on the shaft to the center of the joint.




    Tow Hook Bolt Size
    They are 12mm x 1.25 pitch x 50 mm long with a 19 mm hex head.





    Toyota Vendors - Popular ones
    http://www.12voltguy.com
    http://www.4crawler.com
    http://www.4wdtoyotaowner.com
    http://www.4x4labs.com/
    http://www.4xinnovations.com
    http://www.advanceadapters.com
    http://www.allprooffroad.com
    http://www.bentup.com
    http://www.bigcountrycustoms.com
    http://www.bigrocksoffroad.com
    http://www.bluetorchfab.com
    http://www.budbuilt.com
    http://www.calminitruck.com
    http://www.can-back.com
    http://www.davezoffroadperformance.com
    http://www.diamondaxle.com
    http://www.doaracingengines.com
    http://www.eoronline.com
    http://www.engnbldr.com
    http://www.frontrangeoffroadfab.com
    http://www.gotpropane.com
    http://www.inchwormgear.com
    http://www.lcengineering.com
    http://www.marlincrawler.com
    http://www.offroadsolutions.com
    http://www.ottindustries.com
    http://www.polyperformance.com
    http://www.rockstomper.com
    http://www.ruffstuffspecialties.com
    http://www.shaffersoffroad.com
    http://www.sky-manufacturing.com
    http://www.toyotafiberglass.com/
    http://www.toyotasuperaxles.com
    http://www.wabfab.org
    http://www.YotaMasters.com
    Jeff Mosk Gauge Pods




    Traction Bars
    http://www.pirate4x4.com/forum/showthread.php?t=464319




    Transmissions

    Pickup and 4Runner Transmissions with 1st gear ratios.
    L43 4 speed 79 - 80 3.67
    L45 4 speed 81 - 82 3.93
    L50 5 speed 81 - 82 3.93
    L52 5 speed 83 3.93
    G52 & G54 5 speed 84 - 88 (Carb) 3.93
    W56 5 speed 85 - 95 (EFI) 3.95 Manual Hub Equipped Vehicles 89 and up Have W56, 89 and up ADD vehicles have G58.
    R151F 5 speed 86 - 87 (turbo only) 4.31
    G58 5 speed 89 - 95 3.93 ADD Equipped Vehicles
    R150F (6 cyl) 5 speed 88+ 3.83

    Identification:
    G52/54 84-88' are twin stick, use a 8 bolt center section, 6 bolt gear t/case pattern, 21 spline output.
    G58 89-95' twin stick, 8 bolt center, 9 bolt chain t/case, 26 spline
    W56 85-88' (single stick), 89-95' (twin stick), 10 bolt center, 6 bolt t/case, 21 spline
    R151F 86 - 87 (turbo only) will have two housings of four bolts each just like a G52, the difference would be the large rubber plug on the bottom of the bellhousing.

    Info provided by Marlin Cralwer
    All 84 to 95 22R trans are 25.5" long including the bellhousing. The only shorter trans is the 79-83 year trans which are 20.75" long with bellhousing. These early short trans have had a poor service record due in part to their small bearings and lighter gears. The 82-83 L52 5 speed which had a 80 x 20 mm front input bearing has had the best service record. A number of years ago, I invented a way to install a oversize 80 x 23 mm input bearing with an inproved gear set which features a greater helix angle for added strenght. I call it my L52HD and is the strongest 20.75" long trans.

    Side note:
    ADD = Automatic Differential Disconnect
    For more information see my article here:
    http://www.off-road.com/toyota/tech/add/index.htm

    Tranny 1st 2nd 3rd 4th 5th Rev
    R151f 4.310 2.740 1.930 1.000 0.830 4.230
    W56 3.954 2.141 1.384 1.000 0.850 4.091
    G52 3.929 2.333 1.452 1.000 .851 ????
    FYI: Marlin offers a R151f gear swap that gives 5.15 first

    List of Toyota transmissions which covers all toy trans 2wd, fwd, automatic, car, truck
    http://en.wikipedia.org/wiki/Toyota_transmissions

    A340 Transmission issues and FAQs
    http://www.pirate4x4.com/forum/showthread.php?t=587521

    Converting a W55 4x2 transmission into a W56 4x4
    http://pirate4x4.com/forum/showthread.php?t=586967


    Transfercases

    Years Engine Model Shift Style Spline Type

    1979-1980 20R Carb Top Shift 21-spline
    1981-1983 22R Carb Top Shift 21-spline
    1984-1988 22R Carb Forward Shift 21-spline
    1985-1988 22RE EFI Top Shift 21-spline
    1986-1987 22RTE EFI/Turbo Forward Shift 23-spline
    1989-1995 22RE EFI Forward Shift 21-spline
    89-95 22RE(G58) forward shift chain drive transfercase 26-spline will not accept adapters or gear sets. These are 22RE/4X4 Models with 5 spd and ADD.

    GENERAL LIST OF TOYOTA TRANSFERCASES
    http://www.pirate4x4.com/forum/showp...2&postcount=19

    COMPARISION INFO Marlin 4.7's to AA's 5.0's
    http://www.pirate4x4.com/forum/showt...ht=gear+weaker

    4.7 GEARSET or DUALS?
    http://www.pirate4x4.com/forum/showthread.php?t=109103

    INSTALLATION OF 4.7 GEARS from Marlin Crawler
    http://www.marlincrawler.com/tech/4701-gear-install


    CRAWLER ADAPTER ASSEMBLY INSTRUCTIONS
    http://www.marlincrawler.com/tech/gu...-installer-old

    FRONT WHEEL DRIVE with Toyota T-case
    http://www.pirate4x4.com/forum/showt...hreadid=202342
    http://board.marlincrawler.com/index...;threadid=2397

    DUAL CASE SHIFTERS & CONSOLE ARRANGEMENT
    http://www.pirate4x4.com/forum/showthread.php?t=571627

    TWIN STICK with single forward shift t-case (on the cheap)
    http://www.pirate4x4.com/forum/showthread.php?t=482798

    TRIPLE STICK by Dr Smash
    http://www.pirate4x4.com/forum/showt...t=triple+stick

    TRANSFER CASE PARKING / E-BRAKE COMPARISION Sky's vs AllPro
    http://www.pirate4x4.com/forum/showthread.php?t=214383

    TRANSFER CASE MOUNT TECH
    There are several different styles of T-Case mounts found throughout the years...
    http://www.pirate4x4.com/forum/showt...hreadid=112763
    http://www.pirate4x4.com/forum/showt...ht=case+mounts


    TOP vs FORWARD SHIFT TRANSFER CASE by Chris Gieger
    What is the difference between a top shift and forward shift transfer case. I took a couple of photos showing both top and forward shifting tcases along with matching transmissions. These two photos should make it easier to understand the difference. In both photos the transmission and transfer case have been seprated to show where one ends and the other starts. It also helps show the shift forks on the forward shift setup.

    The first photo shows a top shifting transfer case and transmission. Notice the tcase shifter comes out of the top of the tcase. The transmission has just one shifter. Notice there are no forks on the front of the tcase.


    The second photo is a forward shift transfer case. Notice the blockoff plate on top of the case. This unit is shifted through two rails that connect to the transmission. A forward shift transmission like this one has two shifters, one for the tranny and one for the tcase.


    More Tranny & Transfercase Info
    Code:

    Year Model Application Model Speeds Splines 1st Gear Engine Transfer Case
    1979-1980 Carb L43 4sp 21 spline 3.67 4cyl 20R Gear driven Top Shift
    1981-1983 Carb L45 4sp 21 spline 3.93 4cyl 22R Gear driven Top Shift
    1981-1983 Carb L50 & L52 5sp 21 spline 3.93 4cyl 22R Gear driven Top Shift
    1984-1986 Carb G52 5sp 21 spline 3.93 4cyl 22R Gear driven Forward Shift
    1986-1988 Carb G54 5sp 21 spline 3.93 4cyl 22R Gear driven Forward Shift
    1986-1987 EFITurbo R151F 5sp 23 spline 4.31 4cyl 22RTE Gear driven Forward Shift
    1985-1988 EFI W56 5sp 21 spline 3.95 4cyl 22R Gear driven Top Shift
    1988-1991 EFI R150F 5sp 23 spline 3.83 V6 3.0L Chain driven Forward Shift
    1989-1995 EFI W56 5sp 21 spline 3.95 4cyl 22R Gear driven Forward Shift
    1989-1995 EFI/ADD G58 5sp 26 spline 3.93 4cyl 22R Chain driven Forward Shift
    1996-2002 EFI W59 5sp 23 spline 3.95 4cyl 2.7L Chain driven Top Shift
    1996-2002 EFI R150F 5sp 23 spline 3.83 V6 3.4L Chain driven Forward Shift

    The transfercase/reduction box shift rods on the forward shifting transfercase are different lengths so swapping trannys can cause a problem. Ref:http://www.pirate4x4.com/forum/showt...hreadid=222758
    The G52/G54 trans requires the longer forward type t/case shifting rods. These are only found on 84-88' G carb t/cases, and 86-87' R151F efi turbo t/cases. The 89-95' twin stick W56 with a forward shifting t/case that uses rods that are about 1/2 inch shorter. These shift rods can be easily swapped in the reduction boxes so it just a matter of getting the correct remote shift rod for the tranny. www.MarlinCrawler.com usually has a bunch of both kinds in stock and they can also convert a forward shifting reduction box into a top shifting case for a small cost.

    Flange Patterns:
    More flange pattern measurements

    Flange Pattern dimensions for
    My truck 1989 Extra cab V6 factory 2 peice drive shaft
    tcase/ujoint > 60mmx x60mm x 10mm CSB/ Dual Cardon Joint 60mm x 60mm x 10mm > Rear dif/Ujoint 60mm x 60mm x 10mm

    Flange Pattern dimensions for
    My Brothers truck 1993 Extra cab 22RE factory 2 peice drive shaft
    tcase/ujoint > 60mmx x60mm x 10mm CSB/ Dual Cardon Joint 60mm x 60mm x 10mm > Rear dif/Ujoint 60mm x 60mm x 10mm

    Basically I was worried that the flange pattern on the stock REAR Cv would not work with a triple drilled flange at the tcase. Seems like they will match up since the triple drilled flange has a 60x60x10 pattern.




    Troubleshooting at Home
    READ THIS IF YOUR A NOOB to Mechanics
    http://www.pirate4x4.com/forum/showthread.php?t=430159




    Tube Notching Program
    http://geek.casaforge.com/code/newform_m2.php



    Weber Info by Coop 50

    I live at sea level (hence the name Shoreline) so I can't do much for you, but I believe the people in some of those posts (in the searches) live at high elevation. Perhaps if you contact them by email, they can help you. The other option is to get some small jets and take it from there with a drill set. This is the economical way to do it. I bought a jet kit which also had a double squirt pump jet for more fuel on that initial step on the accelerator.

    What I have read concerning Weber jet adjustment (this is in the search posts), note the original idle jet size, in your case you decrease the size until the mixture screw is optimum at 2 - 3 turns from bottoming out. Whatever size the idle jet turns out to be, you extrapolate what the others should be according to that, because you are setting the jets according to the volume of your engine.

    I have a 32/36, my primary is set pretty good but my secondary is a little rich. I can tell because I have an analog Westach mixture meter hooked up to a heated O2 sensor. If I remember right 13.5 to 1 is optimum for power, 14.7 to one is optimum for clean burning. Another thing I found out is my 86 22R engine naturally runs lean above 3000 rpm (until the secondary kicks in), has something to do with the swirl or flow of the combustion chamber.

    Search Posts:
    http://www.pirate4x4.com/forum/showt...weber+and+jets
    http://www.pirate4x4.com/forum/showt...=weber+jet+kit



    Weight: Ultimate List
    http://www.pirate4x4.com/forum/showthread.php?t=749400


    Wheelbase

    *From the factory manuals:
    1979-83 short bed 101.77 *
    1979-83 long bed 110.24 *
    1984-89 4Runner 102.95 *
    1984-88 xtra cab 112.20 *
    1984-88 single cab short bed 102.95 *
    1984-88 single cab long bed 112.20 *
    1984-88 double cab real short bed 112.20 *
    1990-91 4Runner, 2 door 103.3
    1990-95 4Runner, 4 door 103.3
    1989-95 short bed 103.3
    1989-95 long bed 122.5
    1989-95 xtra cab 122.5
    1995.5-04 Tacoma 105.3 and 121.9
    1996-92 4Runner (taco based) 105.3





    Wheel Bearing Adjustment By SR5Dave

    A good way (at least IMO) to tighten wheel bearings; which allows at least moderately proper preload even with large tires or different offset rims.

    Torque down real tight. Spin wheel once to get everything set. Now back it off. Tighten a little, grab at 12 and 6 and wiggle back and forth. Does it wiggle? Tighten more. Wiggle again. Does it wiggle? Tighten more. Do this until there is basically NO play (Except some from the tires moving back and forth), should be real firm. Now spin the wheel, does it spin at least 1.5 revolutions easily? Good to go.

    Doesn't? Go buy new bearings ya cheap bastard, they're wasted If you can't buy new ones; just find the best point on the curve between little wiggle and enough spin. Make sure one doesn't spin way easier than the other or the freeway will be real interesting.

    This is a good way to do it because you adjust them tighter with bigger tires naturally. Its not perfect, but since Toyota didn't suply us with preload if you put 38" tires and 2"BS rims on.. its 'good enough' IMO. This method gets preload firmer with bigger tires because of a 20" leverage arm on 40" tires instead of 15" lever arm w/ 30"s, further out, easier it is to move the tire, so you tighten it more for less play. Works out pretty good.

    {Comment by 4RnrRick - I feel it should be done using the method in the FSM or Haynes with a pull scale and the adjusted from there for more preload for bigger tires. I'm not sure how much more other than it probably requires more preload to increase bearing life. IMO 'By Feel" is not the best method since everyone does not have the same hands....}



    Wheel / Rim Tech and Info

    Ultimate Beadlock listing.....
    http://www.pirate4x4.com/forum/showt...imate+beadlock


    2" Backspace wheels thread
    http://www.pirate4x4.com/forum/showthread.php?t=197981
    Summit Part Number for US Wheel Reversed Wheel USW-88-5860R-SPEC
    (specify your backspacing) Available as of 6/9/06

    DIY Beadlocks screws by Inchworm
    http://www.pirate4x4.com/forum/showthread.php?t=340906

    Easy way to break the inner bead on Beadlocks
    http://www.pirate4x4.com/forum/showt...89#post6469289

    Moving the valve stem, & adding a quick air down valve to your rims
    http://www.pirate4x4.com/forum/showthread.php?t=407665

    Wheel Spacers / Adapters
    See: http://www.mcmotorsports.com If it physically possible they probably make it.




    Winch: In-Cab Remote Info
    http://www.pirate4x4.com/forum/showthread.php?t=277633




    Winch Rope (Poly / Synthetic )

    How to add a thumble to the end of the rope <-- starts at post #13
    http://www.pirate4x4.com/forum/showthread.php?t=177074

    How to splice two pieces together
    http://www.pirate4x4.com/forum/showt...ght=winch+rope



    Vaccuum Line Diagram
    22R, 22RE, 22RTE diagrams
    http://www.pirate4x4.com/forum/showthread.php?t=579557


    Vacuum Lines - How to clean up engine bay - Lots of 22RE Photos
    http://www.pirate4x4.com/forum/showt...8&page=2&pp=25



    XtraRunner = Xtra cab + 4Runner
    http://www.pirate4x4.com/forum/showthread.php?t=304626



    York and/or OBA (On Board Air) Systems

    Installing a York Compressor using 22R AC brackets
    http://www.pirate4x4.com/forum/showt...hreadid=236027
    http://www.pirate4x4.com/forum/showt...12#post2642612

    Installing a Mini York Compressor on a Supercharged Taco
    http://www.pirate4x4.com/forum/showt...hreadid=177348

    Installing a York Compressor on a T100
    http://home.4x4wire.com/erik/t100/oba.htm

    Converting the Factory AC Compressor to a OBA system
    http://www.pirate4x4.com/forum/showthread.php?t=196622

    York air on a 4.3L powered first gen
    http://www.pirate4x4.com/forum/showthread.php?t=579496


    Factory AC and a Rotary York
    http://www.pirate4x4.com/forum/showthread.php?t=273874

    Check out http://www.onboardair.com/ for all the York accesories and tech info.

    York Oil Blowby Quick Fix
    http://www.pirate4x4.com/forum/showt...47#post2752847


    Or check out this post to see what type of systems people are really using.
    http://www.pirate4x4.com/forum/showt...threadid=98015

    Vehicle Donor List for York / Sanden Compressors! OBA
    http://www.pirate4x4.com/forum/showthread.php?t=276968

    Identifying York Strokes without Part Number-
    here's where I found it
    http://www.mudinyerioffroad.com/yorkOBA.htm
    used to have a runner...


    "I used to go missing quite a lot... Miss Canada, Miss United Kingdom, Miss World." —British soccer bad boy George Best

  7. #7
    Fotograf knixen's Avatar
    Join Date
    Jan 2007
    Location
    Tromsø
    Posts
    4,195

    Default

    Masse karosseri deler til toyota... har til og med sidepaneler til plan hilux mk1... ca 150cad per side...

    http://www.crosscanadaparts.com/our-...html#vancouver
    used to have a runner...


    "I used to go missing quite a lot... Miss Canada, Miss United Kingdom, Miss World." —British soccer bad boy George Best

  8. #8
    Fotograf knixen's Avatar
    Join Date
    Jan 2007
    Location
    Tromsø
    Posts
    4,195
    used to have a runner...


    "I used to go missing quite a lot... Miss Canada, Miss United Kingdom, Miss World." —British soccer bad boy George Best

  9. #9
    Original
    Join Date
    Sep 2010
    Location
    Germany
    Posts
    1

    Default

    Thank you very much for the information. It is very helpful........

  10. #10

    Default

    very useful guide, many thanks.

  11. #11
    Super Moderator Brynjar's Avatar
    Join Date
    Feb 2008
    Location
    KRS
    Posts
    2,975

    Default

    Stikkaksler Hilux og Landcruiser LJ70 :

    '84 Hilux : Lang 800mm, kort 390mm
    CV ca 237mm

    '85 LJ70 : Lang 770mm, kort 410mm
    CV ca 235mm
    ---Insanity is contagious---

  12. #12
    Promodified
    Join Date
    Aug 2008
    Location
    Skien
    Posts
    1,299

    Default

    Fin link for info om bytte av giring, installering av differensialer i diffhus, shimsing, momenter osv. osv.
    Tar for seg så å si alle størrelser av Toyota 4x4 differ.


    http://www.gearinstalls.com
    Mikael Berberg - KNA Telemark
    Tlf: 40634552

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •